/sys/doc/ Documentation archive

/cmd/clone
/cmd/n/ctl
/cmd/n/data
/cmd/n/stderr
/cmd/n/status
/cmd/n/wait

The file ctl controls a connection. When read, it returns the decimal number n of its connection directory. Thus, opening and reading clone allocates a connection directory and reveals the number of the allocated directory, allowing the other files to be named (eg, /cmd/n/data).

Ctl accepts the following textual commands, allowing quoting as interpreted by parsecmd(10.2):

dir wdir

Run the host command in directory wdir, which is a directory on the host system . Issue this request before starting the command. By default, commands are run in the Inferno root directory on the host system.

exec command args ...

Spawn a host process to run the command with arguments as given. The write returns with an error, setting the error string, if anything prevents starting the command. If write returns successfully, the command has started, and its standard input and output may be accessed through data, and its error output accessed through stderr (see below). If arguments containing white space are quoted (following the conventions of sh(1) or parsecmd(10.2)), they are requoted by cmd using the host command interpreter's conventions so that command sees exactly the same arguments as were written to ctl.

kill

Kill the host command immediately.

killonclose

Set the device to kill the host command when the ctl file is closed (normally all files must be closed, see below).

nice [ n ]

Run the host command at less than normal scheduling priority. Issue this request before starting the command. The optional value n, in the range 1 to 3, indicates the degree of `niceness' (default: 1).

The data file provides a connection to the input and output of a previously-started host command. It must be opened separately for reading and for writing. When opened for reading, it returns data that the command writes to its standard output; when closed, further writes by the command will receive the host equivalent of `write to closed pipe'. When opened for writing, data written to the file can be read by the command on its standard input; when closed, further reads by the command will see the host equivalent of `end of file'. (Unfortunately there is no way to know when the command needs input.)

The stderr file provides a similar read-only connection to the error output from the command. If the stderr file is not opened, the error output will be discarded.

Once started, a host command runs until it terminates or until it is killed, by using the kill or killonclose requests above, or by closing all ctl, data and wait files for a connection.

The read-only status file provides a single line giving the status of the connection (not the command), of the form:

cmd/n opens state wdir arg0

where the fields are separated by white space. The meaning of each field is:

n

The cmd directory number.

opens

The decimal number of open file descriptors for ctl, data and wait.

state

The status of the interface in directory n:

Open

Allocated for use but not yet running a command.

Execute

Running a command.

Done

Command terminated: status available in the status file (or via wait).

Close

Command completed. Available for reallocation via clone.

wdir

The command's initial working directory on the host.

arg0

The host command name (without arguments).

The read-only wait file must be opened before starting a command via ctl. When read, it blocks until the command terminates. The read then returns with a single status line, to be parsed using String->unquote (see string(2)). There are five fields: host process ID (or 0 if unknown); time the command spent in user code in milliseconds (or 0); time spent in system code in milliseconds (or 0); real time in milliseconds (or 0); and a string giving the exit status of the command. The exit status is host-dependent, except that an empty string means success, and a non-empty string contains a diagnostic.

Command execution

In all cases, the command runs in the host operating system's own file name space in which emu(1) was started. All file names will be interpreted in that space, not Inferno's. For example, on Unix and Plan 9, / refers to the host's file system root, not Inferno's; the effects of mounts and binds will not be visible; nor will Inferno services be available except by network connection.

On Unix systems, the command is run by the execvp system call, using the Unix user and group ID of the user that started emu(1), unless it was started by the super-user, in which case cmd attempts to set the Unix user ID and group ID to those of a Unix user corresponding to the current Inferno user's name, and failing that, to user and group nobody.

On Plan 9, the command is run with the system call exec, first trying the command name as-is; if that fails and the name does not start with #, /, ./ or ../, cmd attempts to exec /bin/command. The command runs using the Plan 9 identity of the user that started emu(1). Each connection has its own name space.

On Windows systems, the command must be a binary executable (not built into the command interpreter) in the current path. It is always run with the same Windows user identity as started emu(1). The arguments given to the exec request are requoted as described above so as to present the same arguments to the command via the Windows command interpreter. The arguments are otherwise unmodified. In particular, no attempt is made to convert slashes to backslashes in a vain attempt to convert file name syntax to Windows conventions. (In fact, most Windows applications will accept / as a separate in file names, provided the drive letter precedes the whole name to prevent its interpretation as a command option.)